Micronics PCI/ISA System Board D6-IN Manuel d'utilisateur

Index I.Specification of PC Diagnostic Cards…………………………………………………..2 1. Notice……………………………………………………………………………………………2 2. Product Introduction In Brief………

7. Hexadecimal Characters and Particular Characters of Our Cards 8. Meanings of POST codes AMI (00) Going to give control to INT 19H boot loader. (10)

(0B) CMOS status register initialize done. Keyboard controller command byte is written. Going to issue Pin -23, 24 blocking/ unblocking command. Goin

mode set. (18) CH-0 timer test over. About to start memory refresh. Color mode set. (19) 82 timer test over. Memory refresh test to be done next. Ab

ROM and give control. (2D) Optional video ROM control is done. About to give control to do any processing after video ROM returns control. (2E) Return

About to start DMA controller test. (44) Interrupts enabled(if post switch is on). Going to initialize data to check memory wrap around at 0:0. (4

(59) Hit<ESC> message cleared. <Wait..> message displayed. About to start DMA and interrupt controller test. Master 8259 mask register OK,

(83) Command byte written, global data Init done. About to check for lock -key. Check for RS232 ports and put the addresses in global data area. (84

Co-Processor test. (9C) Required initialization before Co-Processor is over. Going to initialize the Co-Processor next. (9D) Co-Processor initialized.

DMA and Interrupt controllers. (D3) DMA controller #1,# 2,interrupt controller #1,#2 disable. Video display is disable and port-B is initialized. Chip

area; Initialize first 120 interrupt vectors with SPURIOUS_INT_HD LR and initialize INT 00h-1Fh according to INT_TBL. Initialize CMOS timer. (09) Prog

I.Specification of PC Diagnostic Cards 1. Notice Notice：Only use this product with guidance of this instruction and under the endurance of it. The sa

DISP LAY ERRORS. 8237 DMA, channel 1 test. (12) Call support 800 -909-3424. Test 8254 timer 0 channel 0. Test DMA page registers. (13) Test 8254 t

ROMs. (32) Display the Award Plug & Play BIOS extension message(PnP BIOS only).Test EISA extended memory; If EISA mode flag is set then test EISA

BIOS data area. Initialize time value; Initialize time value in 40h BIOS data area. (55) Check PCI video Card -or replace video card. (60) Setup virus

(04) Get the CPU type (Beep)=1 -1-2-1.CPU register test. Programmable Interval Timer test failure. (05) [Beep]=1-2-2 DMA initialization in-progress

refresh.(Beep)=1-3-1-1. Upper 16 of 32 bit test failed. (21) [Beep]=3-1-2 slave DMA register test in -progress or failure. (22) [Beep]=3-1-3 mas

(35) [Beep]=4-2-2 shutdown test in progress or failure. (36) [Beep]=4-2-3 gate A20 failure. Warm start shut down . Configure EMS memory option.

test. (64) Jump to User Patch 1.(Beep)=2 -3-2-1.Shadow memory test. (67)Initialize Multi Processor APIC. (68) Enable external and CPU caches.(Beep)=

failure.(Beep)=3 -2-3 -1. (99) Check for SMART Drive(optional). (9A) Shadow option ROMS.(Beep)=3 -2-3-3. (9C) Set up Power Management.(Beep)=3

(E4) Check for forced Flash or initialize system I/O.(Beep)= 4 -3-2. (E5) Check HW status of ROM or check force recovery boot.(Beep)4 -3-2-2. (E6) B

3S System self testinitialization (POST) fails 3S-1S-2SThe second DMA controller failure or register failure 1S-1S-2S Mainboard failure 3S-1S-3SINTMS

all results by codes. With the meaning explanation of the POST codes of this manual, the users can find out what are the problems quickly. Especially

and extended slot Metal sheet in the slot deformed or broken Repair by pliers or replace a new slotMetal sheet rusted or dirtyClean it by pure ethanol

3 CPU overheat protection A.CPU fan not powerful enough or not plugged well Change to a powerful CPU fan, and fix it tightly to CPU B.Heat sinking s

vibration hardware caused by vibration may make the CPU unable to work replace all loose ones or put more nuts to fasten them and enhance their vibrat

indicator 5 3.3V Power Special voltage of motherboards that have PCI slot. The indicator will be always on when power on. Part of the motherboards tha

II. Detailed Specification of Diagnostics & Stability- Test Card 1. Components of Diagnostics & Stability-Test Card （1） Figure of Diagnostic

2. Differences and Functional Characteristics of Diagnostics & Stability-Test Cards and Common Analyzer Cards (1) The Diagnostics & Stabil

36 3. Explanation of Diagnostics & Stability-Test Card Indicator LED Name Function Description 3V Power Special 3V voltage of motherboards tha

than the traditional diagnostic cards do, Kingnostic cards greatly lower the rate of inappropriate operation that lead to a low accuracy in test. 8.

⑥ KLPI4 and KLPI6 can be plugged in PCI, ISA and LPT ports. Their test mode supports kinds of interfaces. 2) There are beep warning functions for KP

endcorrectShow down the power and take out all extended cards. Plug the PC Diagnostic Card in ISA slot (Note: The front side of the component on I

test. You may refer to the computer manual, check it from the CMOS chip on the mainboard or the screen when system is starting, or contact the BIOS su

‐cno Figure 4: press the check switch once more DbDCFigure 5: press the check switch thirdly. Press the check switch fourthly, it goes back to f

four-digit Kingnostic Card. It shows a 2 digit code for each press. And it goes back to show “no” at the sixth press, and the last code that the test